Description
CH-253 is a frosted LDPE e-liquid bottle closed with a press-and-turn child-resistant cap and fitted with a PE tip insert: the cap has to be pushed down before it will turn, and a band under the cap shears onto the neck at the first opening. The body is frosted, so the fill line shows but the liquid does not, and the soft wall delivers the dose by squeeze. The 10 ml set is fixed in the catalogue; the same body is photographed in other heights and those volumes are quoted per project. Bottles ship blank and unprinted.

Quick answer
CH-253 is a blank frosted LDPE e-liquid bottle closed with a press-and-turn child-resistant cap: the cap must be pushed down before it turns, and the band under it shears onto the neck at the first opening, so an opened pack cannot be closed back to look untouched. The neck also takes a PE tip insert that narrows the opening to a drop spout. The 10 ml set is fixed in the catalogue at 2,500 sets per 3# carton; other volumes are quoted per project.
Two locks in one cap
The closure answers two questions at once: can a child open it, and can the buyer tell that nobody has. Pushing down before turning is the child-resistant part — a plain twist does not open the cap, so the motion has to be known. The band under the cap is the tamper-evident part: the first proper opening shears the bridges between band and cap, the band stays on the neck ring, and the pack cannot be closed back to look untouched. Both locks sit in one moulding, so nothing has to be applied on your filling line.
This is the same press-and-turn cap family used on CH-242, which is clear PET; CH-253 puts it on the soft frosted LDPE body so the pack can be squeezed as well as locked.

The cap, the insert, and how the pack closes two ways
Two dispensers work on the same neck. Closed with the cap alone, the bottle is a sealed unit and the neck is covered. Fitted with the PE tip insert — a threaded collar that seats on the neck rim, one flange, and a long tapered spout — the opening narrows to a drop spout, and the same cap closes over the spout, so the pack can ship capped with the insert in place. The insert is a moulded PE spout: not a steel needle, not a glass pipette and not a rubber-teat dropper.


The spout bore sets the drop size, and the bore is stated on the drawing for the insert you order — it is not fixed in the catalogue, so no bore figure is printed here. Tell us the drop count or the dose you need and we check it against the insert tooling before quoting.
Cap colours, and the three-part pack
The cap is moulded in colour, not painted: the photographs show black and white on the same frosted body. A colour-matched cap is a per-colour item, and the minimum quantity per colour is quoted per project because it depends on the colour and the volume you pick. The set is three parts — LDPE body, PP cap, PE insert — and it ships assembled and capped, or bulk-packed as components for your own filling and capping line.

Volume and carton pack
One volume carries a fixed carton specification, and the minimum is a full carton.
| Volume | Material | MOQ (sets) | Sets per carton | Carton | Carton net weight | Unit weight |
|---|---|---|---|---|---|---|
| 10 ml | LDPE bottle, PP cap, PE insert | 2,500 | 2,500 | 3# 53 × 46 × 40 cm | 15.25 kg | 6.10 g |
The family is photographed in several heights, but only the 10 ml has a catalogue line: the other volumes each need their own body tooling and their own minimum, so they are quoted per project rather than printed here. Height, body diameter, neck finish and insert bore are stated on the drawing for the volume you order. Lead times, print minimums and mixed-volume shipments are quoted per project.
Child-resistant, and what that means for your market
The mechanism is a press-and-turn closure, which is the design most child-resistant e-liquid packs use. Whether a pack passes the protocol of the market you sell into is settled by testing, and the test runs on the filled pack, not on the empty bottle: it covers cap removal, the closure staying shut after the test, and the pack holding its contents. We supply samples for that test; we do not publish a third-party certificate for this set, so plan the test into your launch rather than after it.
Two practical notes. The press-and-turn motion is harder for elderly or weak-grip users than a plain screw cap, which is why some markets allow a non-child-resistant format for certain products — check which one applies to you. And a legend or a braille field on the cap band is cut into the mould insert, so wording and position are fixed once the tool is made; say so before tooling, not after.
Applications
Small doses of liquid that has to be kept away from children and sold in a pack that shows it is unopened:
- Nicotine salt and e-liquid packs, 10 ml being the common sample and travel size
- Nicotine shots, boosters and flavour concentrates
- CBD, essential oil and aromatherapy blends in small doses
- Liquid medicines and supplements dosed by drops
- Adhesives, oils and reagents in small workshop doses
LDPE is soft and squeezes, so the dose is delivered by pressure rather than by tilting. The resin carries no barrier layer and the pack is not qualified as pharmaceutical primary packaging: test the formulation in a filled sample before a production run, and check the pack against the rules of the market you sell into.
Where CH-253 sits in the range
CH-253 is the child-resistant build on the frosted LDPE body: press-and-turn cap, tip insert, squeeze dosing. CH-252 is the same frosted body without the child-resistant action — a cone-nose cap that turns off with a normal twist and records the first opening with a band. CH-242 is the press-and-turn cap on clear PET in 10 and 20 ml. CH-152 covers frosted LDPE from 5 to 120 ml with a break-ring cap, and CH-153 is clear PET in 5, 8 and 10 ml with a plain cap.

OEM, decoration and documentation
Bottles ship blank and unprinted. A printed body, a labelled body, a colour-matched cap or a custom insert bore is an OEM item: label, silk screen and offset print are your artwork, and the bottle carries no logo or certification mark as supplied. Print minimums and per-colour minimums are quoted per project.
Certification documents are available upon request.
Request a sample or a quotation
Send the volume, the liquid, the cap colour, the market you sell into and your annual quantity. We reply with a drawing check, a sample plan and a quotation. Contact: info@chmib.com.
FAQ
Is CH-253 child-resistant?
Yes. The cap is a press-and-turn closure: it has to be pushed down before it will turn, and the band under the cap shears onto the neck at the first opening. No third-party certificate is published for this set, and the protocol of your market is settled by testing the filled pack, so plan that test into your launch; we supply samples for it.
What volume does CH-253 come in?
10 ml is the volume fixed in the catalogue: 2,500 sets as the minimum and 2,500 sets per 3# carton of 53 x 46 x 40 cm, 15.25 kg net. The body family is photographed in other heights, and those volumes are quoted per project against their own drawing and minimum.
Does the cap come with the tip insert?
The set is three parts: LDPE body, PP press-and-turn cap and PE tip insert. It ships assembled and capped with the insert in place, or bulk-packed as components for your own filling and capping line.
Which cap colours are available?
The caps are moulded in colour; the photographs show black and white on the same frosted body. The minimum quantity per colour depends on the colour and the volume, so it is quoted per project.
How is CH-253 different from CH-252?
Same frosted LDPE body and the same kind of PE tip insert, different closure. CH-253 uses the press-and-turn child-resistant cap, so it needs a push before it turns. CH-252 uses a cone-nose cap that turns off with a normal twist and records the first opening with a band, which suits markets that do not require a child-resistant closure.
Can the bottle be printed, or the cap carry a legend?
Yes, as an OEM item. Label, silk screen and offset print use your artwork, and the bottle carries no logo as supplied. A legend or braille field on the cap band is cut into the mould insert, so wording and position are fixed once the tool is made; print minimums are quoted per project.



